50 Watt Amplifier

Home > Circuits > Sound/Radio > 50 Watt Amplifier

Search:

Author	Views	Views Today	Rank	Comments
	519,409	54		74

Schematic

Parts

Part Total Qty. Description Substitutions R1 1 200 Ohm 1/4 W Resistor R2 1 200K 1/4 W Resistor R3 1 30K 1/4 W Resistor R5 1 1K 1/4 W Resistor R6 1 5K 1/4 W Resistor R7,R10 2 1 Meg (5%) 1/2 W Resistor R8,R9 2 0.4 Ohm 5 W Resistor R11 1 10K Pot R12,R13 2 51K 1/4 W Resistor R14 1 47K 1/4 W Resistor C1 1 100uF 35V Electrolytic Capacitor C2 1 0.011uF Capacitor C3 1 3750pF Capacitor C4,C6 2 1000pF Capacitor C5,C7,C8 3 0.001uF Capacitor C9 1 50pF Capacitor C10 1 0.3uF Capacitor C11,C12 2 10,000uF 50V Electrolytic Capacitor U1,U2 2 741 Op Amp U3 1 ICL8063 Audio Amp Transister Driver thingy Q1 1 2N3055 NPN Power Transistor Q2 1 2N3791 PNP Power Transistor BR1 1 250 V 6 Amp Bridge Rectifier T1 1 50V Center Tapped 5 Amp Transformer S1 1 SPST 3 Amp Switch S2 1 DPDT Switch F1 1 2 Amp Fuse SPKR1 1 8 Ohm 50W Speaker MISC 1 Case, Knobs, Line Cord, Binding Posts Or Phono Plugs (For Input And Output), Heatsinks For Q1 And Q2

Notes

1. I know I skipped R4. That is not a problem :-)
2. Distortion is less than 0.1% up to 100HZ and increases to about 1% at 20kHz.
3. I haven't been able to find anyone who sells a suitable T1. You can always use two 24V 5A units in series. If you are building two amps (for stereo), then I would suggest using an old microwave transformer and rewinding it. Follow the instructions in the 12V To 120V Inverter, execpt wind 26 turns, twist a loop (center tap) and wind 26 more turns. That should work out to around 50 volts. You may need to add or remove turns depending on your transformer.
4. Q1 and Q2 will require heatsinks.
5. You may have trouble finding U3 because it is discontinued. Please don't email me about sources...I can't find it either. See if any of the sources in Where To Get Parts has it. A possible source was sent in by JBWilliams:

   Zigma Electronics
   8803 Shirless Ave.
   Northbridge, CA 91324
   United States
   Phone: 818-772-7590
   

If you would like to leave a comment, you can do so using the form below. Comments can be things like suggestions, successes or failures, improvements, similar circuits, error reports, an answer to a previous commenter's question, or anything in between. However if you would like to ask a question it is suggested that you use the forum instead. The forum provides a more robust environment for discussion.

Important: If you post a technical question here, there is no guarantee it will be answered. All technical questions should be posted to the forum. The owner of this site generally does not answer questions in comments.

All comments are subject to approval before they are displayed here, so your comment will not appear immediately. This is done mainly to prevent spam and other abuse. If you wish to remain anonymous, simply enter "anonymous" for your name and/or email.

Name:
Email:
Subject:
Comments:
Anti Spam Code:	Please enter the exact text shown in the image above into the box below. Browser cookies must be enabled to comment on circuits.
Privacy Policy

Back To Circuits Page | Mail Me | Search |